Debugging Simulated Code
gem5 has built-in support for gdb's remote debugger interface. If you are interested in monitoring what the code on the simulated machine is doing---the kernel (in FS mode) or program (in SE mode)---you can fire up gdb on the host platform and have it talk to the simulated gem5 system as if it were a real machine/process (only better, since gem5 executions are deterministic and gem5's remote debugger interface is guaranteed not to perturb execution on the simulated system).
If you are simulating a system that uses a different ISA from the host you're running on, you'll need a cross-architecture gdb; see below for instructions. If you are simulating the native ISA of your host, you can very likely just use the pre-installed native gdb.
When gem5 is run, each CPU listens for a remote debugging connection on a TCP port. The first port allocated is generally 7000, though if a port is in use, the next port will be tried.
To attach the remote debugger, it's necessary to have a copy of the kernel and of the source. Also to view the kernel's call stack, you must make sure Linux was built with the necessary debug configuration parameters enabled. To run the remote debugger, do the following:
ziff% gdb-linux-alpha arch/alpha/boot/vmlinux GNU gdb Copyright 2002 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "--host=i686-pc-linux-gnu --target=alpha-linux"... (no debugging symbols found)... (gdb) set remote Z-packet on [ This can be put in .gdbinit ] (gdb) target remote ziff:7000 Remote debugging using ziff:7000 0xfffffc0000496844 in strcasecmp (a=0xfffffc0000b13a80 "", b=0x0) at arch/alpha/lib/strcasecmp.c:23 23 } while (ca == cb && ca != '\0'); (gdb)
The gem5 simulator is already running and the target remote command connects to the already running simulator and stops it in the middle of execution. You can set breakpoints and use the debugger to debug the kernel. It is also possible to use the remote debugger to debug console code and palcode. Setting that up is similar, but a how to will be left for future work.
If you're using both the remote debugger and the debugger on the simulator, it is possible to trigger the remote debugger from the main debugger by doing a 'call debugger()'. Before you do this you'll need to figure out what CPU (the cpu id) you want to debug and set current_debugger to that cpuid. If you only have one cpu, then it will be cpuid 0, however if there are multiple cpus you will need to match the cpu id with the corresponding port number for the remote gdb session. For example, using the following sample output from M5, calling the kernel debugger for cpu 3 requires the kernel debugger to be listening on port 7001.
%./build/ALPHA/gem5.debug configs/example/fs.py ... making dual system Global frequency set at 1000000000000 ticks per second Listening for testsys connection on port 3456 Listening for drivesys connection on port 3457 0: testsys.remote_gdb.listener: listening for remote gdb #0 on port 7002 0: testsys.remote_gdb.listener: listening for remote gdb #1 on port 7003 0: testsys.remote_gdb.listener: listening for remote gdb #2 on port 7000 0: testsys.remote_gdb.listener: listening for remote gdb #3 on port 7001 0: drivesys.remote_gdb.listener: listening for remote gdb #4 on port 7004 0: drivesys.remote_gdb.listener: listening for remote gdb #5 on port 7005 0: drivesys.remote_gdb.listener: listening for remote gdb #6 on port 7006 0: drivesys.remote_gdb.listener: listening for remote gdb #7 on port 7007
Getting a cross-architecture gdb
To use a remote debugger with gem5, the most important part is that you have gdb compiled to work with the target system you're simulating (e.g. alpha-linux if simulating an Alpha target, arm-linux if simulating an ARM target, etc). It is possible to compile an non-native architecture gdb on an x86 machine for example. All that must be done is add the --target= option to configure when you compile gdb. You may also get pre-compiled debuggers with cross compilers. See Download for links to some cross compilers that include debuggers.
% wget http://ftp.gnu.org/gnu/gdb/gdb-6.3.tar.gz --08:05:33-- http://ftp.gnu.org/gnu/gdb/gdb-6.3.tar.gz => `gdb-6.3.tar.gz' Resolving ftp.gnu.org... done. Connecting to ftp.gnu.org[22.214.171.124]:80... connected. HTTP request sent, awaiting response... 200 OK Length: 17,374,476 [application/x-tar] 100%[====================================>] 17,374,476 216.57K/s ETA 00:00 08:06:52 (216.57 KB/s) - `gdb-6.3.tar.gz' saved [17374476/17374476]
% tar xfz gdb-6.3.tar.gz % cd gdb-6.3 % ./configure --target=alpha-linux <configure output....> % make <make output...this may take a while>
The end result is gdb/gdb which will work for remote debugging.
If you're planning to debug an ARM kernel you'll need a reasonably new version of gdb (7.1 or greater). Additionally, you'll have to manually specify the tspecs like this (port number may be different). The tspec file is available in the gdb source code:
set remote Z-packet on set tdesc filename path/to/features/arm-with-neon.xml symbol-file <path to vmlinux used for gem5> target remote <ip addr of host running gem5 or if local host 127.0.0.1>:7000